Please follow the steps below to complete your installation of NETePay TSYS (Summit) Host EMV - VRH 5.06.15 Rental

Step 1 - Install Client Control

In order to communicate with this NETePay your POS may use one of the following ActiveX controls depending on the integration method chosen by the POS developer. If you are unsure of which to install please contact POS technical support.

dsiEMVUS® 1.48

Release date: 09/14/2020

Datacap’s out-of-scope ActiveX control for NETePay supporting a variety of EMV-enabled hardware options.

For information on supported devices please see our PC based POS solutions page.

Release notes for v1.48

  • Added Ingenico iUC285 with E2E for VANTIV (Worldpay Core). Supported as an attended device since only attended Ingenico devices are certified with VANTIV. NETePay EMV Support should be set to Credit and the CVM to None.
  • For Ingenico devices, manual card input, new logic checking for POS initiated cancel.
  • For Ingenico devices, send 15.9 command for Tetra and RBA versions greater than 17.02. This allows older RBA versions to perform fallback to MSR.
  • For Verifone devices, when POS initiated cancel occurs, S00 command is now sent to terminate the current command (S11, S12, S16) so that a subsequent pad reset runs clean.
  • IDTech device ID value fixed mapping to the correct VID/PID values.
  • EMV Debit is sent to NETePays for all swipe and/or fallback to swipe transactions rather than a non-EMV Debit. If an older NETePay supports EMV Credit and swipe Debit (never supported EMV Debit), then an older dsiEMVUS control is required.

New build released 9/22/20 - <PayAPI_Id> is now passed through if returned by NETePay Hosted.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

dsiPDCX® 1.70

Release date: 08/28/2020

Datacap’s out-of-scope ActiveX control for NETePay and GIFTePay software that supports dozens of plug and play hardware options, including PIN Pads, Mag stripe readers, all-in-one touch terminals and contactless readers.

Release notes for v1.70

  • Support is added for a new command called GetPrePaidStripeTk1 used to return Track1 card data as long as the card number is not a major credit card.
  • Support is added for the Verifone M400 for Worldpay IP (Mercury) with 3DES DUKPT PAN encryption.
  • Support is added for the Verifone M400 for the NETePay Hosted environment with 3DES DUKPT PAN encryption.
  • Support is added for the Verifone M400 for First Data Rapid Connect with 3DES DUKPT PAN encryption.
Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro

OR

DSIClientX® 3.86

Release date: 09/01/2011

Datacap’s long-standing in-scope ActiveX control for NETePay and GIFTePay software.

Microsoft Windows 10 Pro / 8 Pro / 7 Pro / Vista Pro / XP Pro
Step 2 - Install NETePay TSYS (Summit) Host EMV - VRH 5.06.15 Rental

Release date: 05/18/2017

  • Support for eCommerce merchant category
  • Support for a new Adjust transaction is added
    • The new Adjust transaction is used to adjust the purchase amount downward after the original Sale. The trigger for the new Adjust transaction is the <OriginalAuthorized> amount tag. If an Adjust (or AdjustByRecordNo) transaction includes the <OriginalAuthorized> amount and the total amount is less than the original authorized amount, then the new TSYS Adjustment transaction is performed to adjust the transaction amount downward. Without the <OriginalAuthorized> amount tag, an Adjust transaction will simply adjust the TIP amount as for previous releases.
  • Support for Pay At The Table (PATT) server (This functionality is currently only available via closed beta)

New build 8/30/17 - Change to contactless parameters sent on EMVParamDownload (MSD only)

Microsoft Windows 10 Pro / 8 Pro / 7 Pro (Windows XP and Vista do not support TLS 1.2 which is now an industry requirement)